New Honda CRF 300 Rally and oil change

 So we moved to northern Thailand and riding single tracks in the jungle these days. The 690 would not cut it as it is too clumsy so needed a more nimble toy to play with. The answer was a pimped up Honda CRF 300 Rally.



I have only ridden it for a few months but already stacked up 7000+ km so really time for an oil change. Well, by the book it is 12k km but since I ride dirt it should really be at 3-4k km intervals. Anyway below are the quick steps on this very simple oil change.


Parts needed


Oil filter


Crush washer


1.5 liter fully synthetic oil


Oil filter box gasket

Drain oil


Use a brake cleaner to clean the outside of the crank case

 

Remove drain plug and take away the crush washer


Raise bike upright and wiggle it until all oil is out. Put back the drain plug with the new crush washer on.

Replace oil filter


Remove oil filter cover on right hand side 


Remove oil filter and pay attention to spring


Clean with brake cleaner


Put new filter in




Fit new gasket on lid

 



Put cover back on paying attention to the spring and fasten the 4 screws.


Fill oil



Using a funnel fill 1.5 liter of oil


Use fully synthetic 10W+40


Run the engine warm for 5 minutes


Record the milage


Put the bike straight up and check that there is sufficient oil in the sighting glass

Comments

Post a Comment

Popular posts from this blog

Getting stuck in New Territories

Image
Last Sunday the weather was great and I hadnt been out riding for a while so thought I would head out for a ride. Not having ridden for a few weeks I noted the battery had gone flat. I took it out and put it on charge for an hour while having breakfast. Normally I charge it longer but I was keen on getting out on the road and while riding the bike the battery is getting charged so didn't worry to much of having a flat battery. I was just coming over the mountain range on Route Twisk, where plenty of sport bikes go racing, when I noticed I was low on fuel. I pulled into a gas station and filled the bike up. Once I was ready to go I turned the ignition back on but nothing happened when I pushed the start button. Since the light came on and the headlight looked fine it wasn't obvious what was wrong. The most obvious sign was that the service light was showing after a few seconds when turning the ignition on. I thought maybe the ECU, the bikes computer, had gone wrong so ...
Read more

A new set of tyres and tubes

Image
  Since I've been riding around on the same tyres for the past 6 years I reckon it made sense to put on a new set of tyres. Not that the old ones were totally used up but it just felt better to have fresh rubber when you start the trip. I also like to put in heavy duty (3mm) or ultra heavy duty (4mm) inner tubes to minimize the risk of punctures. The tools needed Lift the front wheel off the ground with the enduro stand. Undo the four front bolts with a torx key and undo the main bolt with a big wrench. Empty the tyre of air by removing the valve stem (if you have the tool) or just pressing down the little spike inside the valve. Put the tyre on top of the new tyre and break the bead so the tyre comes off from the rim. Repeat on other side. You can also use the tyre irons to help doing this. Start about 20 cm right of the valve with one tyre iron and another 20 cm further away to get the tyre off the rim. Press down the tyre on the other side so it stays in the center drop to give ...
Read more

Reverse bleeding the clutch

Image
  On a bike the clutch is a pretty useful thing to have working. I have had a couple of incidents in the past with non working clutch, in southern Brazil and in Holland, and it is a pain especially when starting the bike. However, the clutch is not as critical as in a car and especially at speed you can change gear without using the clutch. I heard MX riders prefer to do it instead of letting go of critical fingers on the handlebar. However, given I have time before departure and the fact I haven't even change the clutch fluid once since I bought the bike I reckon it was about time anyway to give it some love. First of all you need some tools. A large syringe with a hose and some new fresh hydraulic fluid. I found some of the Motorex hydraulic fluid in the bike shop nearby. A second syringe is handy as well to empty the master cylinder with and this one needs no hose. Key tools is a 8mm wrench for the bleeder valve on the slave cylinder and a 5mm hex key to loosen the master cylind...
Read more